Where Commercial Buildings Leak
The roof gets blamed for most water intrusion and causes a minority of it. On the buildings we are called to, the entry point is more often a failed sealant joint, a parapet cap, a window perimeter, or a termination where two systems meet and neither trade owned the detail. Water enters at that point, runs along a slab edge or behind the cladding, and shows up on a ceiling two floors down and forty feet away.
That is why the first visit is diagnostic rather than corrective. We work from the interior evidence back to the likely path, then confirm it with controlled water testing before anyone specifies a repair. Sealing the wrong joint is expensive, and it teaches you nothing about the real one.
Common Leak Points and How They Get Fixed
| Where it leaks |
What fails |
The fix |
Service |
| Below-grade and foundation walls |
Membrane defects under hydrostatic pressure from groundwater, and cracks a rigid coating cannot bridge as North Texas clay swells and shrinks |
A positive-side membrane with drainage, installed during construction. Afterward, injection grouting at active cracks and treatment from the inside face |
Below-grade waterproofing |
| Plaza decks, balconies, walkways and parking decks |
Membrane failures at drains, expansion joints, planter penetrations and wall transitions. On coated decks, a worn wear coat or moisture rising through the slab and pushing the coating off |
A pedestrian or vehicular coating system matched to the traffic, applied after a moisture test and mechanical profiling of the concrete. The wear coat is typically renewed every five to ten years |
Deck coating systems |
| Sealant joints and expansion joints |
Sealant that has pulled loose along one edge or split because it went in without backer rod. Expansion joints filled with rigid material during a renovation |
Old sealant cut out and the joint rebuilt with backer rod and new sealant. Larger movement joints get a manufactured cover system that moves with the building |
Joint sealing and expansion joint systems |
| Windows and storefronts |
Gaskets that have hardened and shrunk with age, and failed perimeter sealant |
Wet glazing at the glass-to-frame line, or new perimeter sealant. Water testing comes first, to confirm the leak is at the window and not somewhere above it |
Window glazing and caulking |
| Masonry and concrete walls |
Water moving through the wall (efflorescence is the sign), cracks, spalling over corroded steel, and gaps in the air barrier at transitions |
Spalls repaired back to sound concrete and cracks routed and sealed before a breathable silane or siloxane repellent goes on. Air barrier gaps sealed so the barrier runs continuously |
Concrete and masonry, plus air and vapor barriers |
| Roof edges and parapet copings |
Terminations where the roof meets the wall and neither trade owned the detail |
The termination rebuilt as one detail, with coping and edge metal formed to ANSI/SPRI ES-1 in our own shop |
Sheet metal fabrication |
Below-Grade and Plaza Deck Waterproofing
Below-grade work is the least forgiving waterproofing there is, because you rarely get a second chance at the positive side once the structure is backfilled. Foundation walls, elevator pits, and tunnels all sit under constant hydrostatic pressure, and a defect that would be trivial above grade becomes a permanent maintenance problem below it.
Plaza decks and occupied roof surfaces carry a related problem: the waterproofing membrane sits under pavers, planters, or topping slab, so failures are invisible until they surface inside. Expansion joints, drain assemblies, and planter penetrations are the usual culprits. We detail those transitions before the wearing surface goes down, and when we are brought in after the fact, we locate the breach by zone so the demolition stays surgical.
How to Choose a Commercial Waterproofing Contractor
Ask how they will find the leak before you ask what the repair will cost. A contractor who quotes a sealant scope from the parking lot is guessing at the entry point. Diagnostic water testing, such as a calibrated hose test under AAMA 501.2 at windows and storefronts, should come before the scope is written. On a new deck membrane, a flood test under ASTM D5957, run before anything covers the membrane, is how you know it keeps water out.
Then ask whose system they install and whose warranty you get. Waterproofing manufacturers approve the applicators who install their systems, and their warranties generally apply only to work an approved applicator installed. The warranty may be materials-only, which replaces product that fails, or labor-and-material, which also covers the cost of putting it right. Get the type and the exclusions in writing before work starts.
Transitions deserve their own question. Where waterproofing meets the roof, at a roof-to-wall expansion joint or where a plaza deck meets the building wall, two trades and two product lines come together, and those details leak when nobody owns them. We hold both the roofing and the waterproofing scope, so those transitions are designed as one detail and sequenced with the roof work.